4
variant 25A
DESCRIPTION
LIMIT
LOW
SIGNAL
ON
LIMIT
HIGH
INPUT
LOOP
THRU
1 UNITS
2 UNITS
Array eq
WARNING!
MAX. 10 UNITS INAPR
ALLEL
220V-240V 2A
50H
z/60Hz
FOR
CONTIN
UED PROTECTIONAGAINST RISK
OF F
IRE REPLACE ONYLWITH THE SA
ME TYP
E
WARNING: THIS PRODUCT MUSTBE GROUNDED
ATENCIÓN:ESTE APARATO DEBE CONECTARSE ATIERRA
NO EXISTEN PARTES AJUSTABLES POR EL USUARIO EN EL INTERIOR DE ESTE EQUIPO
REFER TO INSTRUCTIONS MANUAL FOR CONNECTION
NO USER SERVICEABLE PARTS INSIDE
VEASE MANUAL DE INSTRUCCIONES PARA LA CONEXIÓN
ACHTUNG: DIESE PRODUKT MUSS GEERDET SEIN
ANSCHLUSSWEISE BITTE DER ANLEITUNG ENTNEHMEN
ES SIND KEINE VOM ANWENDER EINSTELLBAREN TEILE IM GERAET VORHANDEN
ATTENTION:CE PRODUIT DOIT ETRE RELIE A LATERRE
VOIR MANUEL D'INSTRUCTIONS POUR LA CONNEXION
AUCUNE PIÉCE N’ESTAJUSTABLE PAR L’UTILISATEUR Á L’INTERIEUR DE CETAPPAREIL
D.A.S. AUDIO S.A. (Valencia) SPAIN
CAUTION
ATTENTION
risk of electric shock
do not open
danger d’electrocution
ne pas ouvrir
AC
OUTPUT
T2A L 250V FU
SE
AC
INPU
T
Serial Number:
®
Variant-25AVariant-25A
EUROPEAN
PRODUCT
N1918
Made in Spain
B
G
H
D
E2
E1
A
F
C
0.15AIdle
1/8 Power
1/3 Power
Pink noise
0.7AMaximum power
variant 25A
0.3A
0.45A
Current consumption
Data obtained at 230V, multiply per 2 for 115V.
Maximum power: Measured in conditions of severe
clipping.
AC power requirements
The required voltage for all models is:
115V, 50Hz/60Hz - 230V, 50Hz/60Hz
Maximum voltage (divide by 2 for 115V):
255V
Shutdown voltage for variant 25A (divide by 2 for
115V):
160V
Rear amplifier panel on variant 25A systems.
G) LOOP THRU:
H) ARRAY EQ: In order to compensate for the
summing of the mid and low frequencies, the
onboard signal processing of each variant 25A unit
provides high frequency boost. The signal
treatment has been designed to provide optimum
response for arrays of 6 or more cabinets, so
when employing just two or three units it may be
appropriate to lower the high frequency level. The
ARRAY EQ switch can be used to attenuate the
equalization of the very high frequencies in -3 dB
steps.
Used for paralleling several
units, which will share the same input. The output
can also be used to provide signal for an outboard
power amplifier.
The variant 25A is a two way class AB self
powered system. Nominal amplifier power
(Continuous) per way: LF:125 W HF:75 W.
Amplifier panel description:
A) LIMIT: A
B) SIGNAL:
C) ON:
D) FUSE.
E1) AC INPUT: Blue
E2) AC OUTPUT: W
10 (at 230V)
F) INPUT:
1=GND (ground)
2=(+) Non inverted input
3=(-) Inverted input
mplifier limiter indicator lights. When
lit, the level of the signal source should be
reduced.
Signal presence indicator at the
amplifiers' inputs.
Indicator light for each amplifier
channel.
PowerCon® NAC 3 FCA
connector. Only when the connector is inserted
and rotated (clicked) into place will the AC turn on.
The connector can be used as a switch, rotating
the connector to or from the locked position will
turn the unit on or off, respectively. Mute the signal
feeding the INPUT before turning the unit on or
off.
hite PowerCon® NAC 3
DFCB connector. This is used as an AC loop thru
so that up to boxes can be powered
from a single AC line.
Balanced signal XLR. Pin
assignments as follows :
Manual del Usuario / variant / User’s Manual
(28 paginas)
(39 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales